40 = FAN COIL UNIT
MH = MODEL
H = HIGH WALL / INDOOR FAN COIL TYPE
Q = HEAT PUMP / PRODUCT FAMILY
18 = 1.5 TON / NOMINAL CAPACITY
--- = Not Used
3 = 208-230-1-60 / VOLTAGE
The 40MHH series ductless systems are a matched combination of an outdoor condensing unit and an indoor fan coil unit connected only by refrigerant tubing and wires.
The fan coil is mounted on the wall, near the ceiling. This selection of fan coils permits creative solutions to design problems such as:
- Add-ons to current space (an office or family room addition)
- Special space requirements
- When changes in the load cannot be handled by the existing system
- When adding air conditioning to spaces that are heated by hydronic or electric heat and have no ductwork
- Historical renovations or any application where preserving the look of the original structure is essential.
These compact indoor fan coil units take up very little space in the room and do not obstruct windows. The fan coils are attractively styled to blend with most room decors. Advanced system components incorporate innovative technology to provide reliable cooling performance at low sound levels.
LOW SOUND LEVELS
When noise is a concern, the ductless systems are the answer. The indoor units are whisper quiet. There are no compressors indoors, either in the conditioned space or directly over it, and there is none of the noise usually generated by air being forced through ductwork.
If security is an issue, outdoor and indoor units are connected only by refrigerant piping and wiring to prevent intruders from crawling through ductwork. In addition, since the outdoor units can be installed close to an outside wall, coils are protected from vandals and severe weather.
This compact ductless system is simple to install. A mounting bracket is standard with the indoor units and only wire and piping need to be run between the indoor and outdoor units. These units are fast and easy to install ensuring minimal disruption to customers in the home or workplace. This makes the ductless systems the equipment of choice, especially in retrofit situations.
SIMPLE SERVICING AND MAINTENANCE
Removing the top panel on outdoor units provides immediate access to the control compartment, providing a service technician access to check unit operation. In addition, the draw-thru design of the outdoor section means that dirt accumulates on the outside surface of the coil. Coils can be cleaned quickly from the inside using a pressure hose and detergent.
On all indoor units, service and maintenance expense is reduced due to easy-to-use cleanable filters. In addition, these high wall systems have extensive self-diagnostics to assist in troubleshooting.
Ductless system indoor and outdoor units are designed to provide years of trouble-free operation.
The high wall indoor units include protection against freeze-up and high evaporator temperatures on heat pumps.
The condensing units on heat pumps are protected by a three minute time delay before the compressor starts the over-current protection and the high temperature protection.
INDIVIDUAL ROOM COMFORT
Maximum comfort is provided because each space can be controlled individually based on usage pattern. The air sweep feature provided permits optimal room air mixing to eliminate hot and cold spots for occupant comfort. In addition, year-round comfort can be provided with heat pumps.
The ductless system design allows individual room heating or cooling when required. There is no need to run large supply-air fans or chilled water pumps to handle a few spaces with unique load patterns. In addition, because air is moved only in the space required, no energy is wasted while air moves through the ducts.
The high wall units have microprocessor-based controls to provide the ultimate in comfort and efficiency. The user friendly wireless remote control provides the interface between the user and the unit.
Customizing these ductless systems to your application is easily accomplished.
Adding a condensate pump accessory to the high wall fan coil provides installation flexibility.
OPTIONAL WIRED CONTROLLER
All systems are listed with AHRI (Air Conditioning, Heating & Refrigeration Institute), and ETL.
|Weight||31.97 Pounds (lbs)|
|Width||38.36 Inches (In)|
|Height||12.8 Inches (In)|
|Country of Origin||CHN|
|Length||8.87 Inches (In)|
|Blower Motor HP||1/27 HP|
|Blower Motor RPM||1150|
|Blower Motor Speeds||4|
|Blower Motor Type||Fixed Torque|
|Circuit Breaker - Max Amps||0|
|Circuit Breaker - Min Amps||0|
|Drain Connection Size||.625"|
|Liquid Line Fitting||Not Provided|
|Liquid Line Size||1/4"|
|Maximum Fuse Size||0|
|Maximum Piping Height||Not Provided|
|Maximum Piping Length||Not Provided|
|Minimum Circuit Amps||0.28|
|Rated Current Amps||0.28|
|Rated Load Amps||0|
|Suction Line Fitting||Not Provided|
|Suction Line Size||1/2"|